Spot Zero Built-in Systems · Watermakers & Water Purifiers

Spot Zero XZ II Combination Watermaker + Water Purifier — 900 to 2,200 GPD seawater, up to 3,000 GPD purified

คำสั่งซื้อพิเศษ — ยืนยันเวลานำส่งที่ระบุตอนชำระเงิน

Seawater in, spot-free bottled-quality water out, from one frame: SeaXchange watermaker (900–2,200 GPD) and ZTC II purifier (1,000–3,000 GPD) combined, modular or stacked. 230 V 50/60 Hz. Price on request.

Genuine Spot Zero, ordered from the factory in Fort Lauderdale with Drake Marine's sizing, factory liaison and commissioning support
Spot Zero's standard limited warranty — we register the system and handle any claim for you from Thailand
Questions before you buy? LINE @drakeco หรือ WhatsApp +66 99 406 4680
Special order — we confirm the factory lead time and the dispatch date with you before payment; special-order items are returnable if faulty
Pay by bank transfer (SCB) or PayPal — cards accepted through PayPal. International freight at cost, invoiced separately

การจัดส่งและการขนส่ง

จัดส่งฟรีในพื้นที่ — ตรัง · กระบี่ · ภูเก็ต
บริการจัดส่งทั่วประเทศไทย โดยปกติใช้เวลา 1-3 วัน
จัดส่งทั่วโลกโดยบริการจัดส่งด่วนและทางเรือ

ตรวจสอบราคายุติธรรม

ราคาของเราคือราคาขายปลีกแนะนำ (RRP) ของผู้ผลิตในตลาดภายในประเทศ — คือราคาที่อุปกรณ์นี้ถูกขายในประเทศที่ผลิตขึ้น อุปกรณ์ทางทะเลที่มีแบรนด์ในไทยมักมีราคาขายปลีกสูงกว่าราคาดังกล่าว 15–90% เมื่อมีข้อมูลราคาที่เปิดเผยออกมา แต่สินค้าของเราไม่มีข้อมูลราคาดังกล่าว.

ก่อตั้งปี 2002 ประสบการณ์ทางทะเลมากกว่า 20 ปี ยุติธรรม การกำหนดราคาราคาขายปลีกแนะนำ (RRP) ในตลาดในประเทศ

เกี่ยวกับผลิตภัณฑ์นี้

เดอะ Spot Zero XZ II is the flagship: a SeaXchange XTC II watermaker and a ZTC II double-pass purifier engineered into a single system. Seawater goes in; fresh water comes out of the first stage; the second stage takes that water down to about 10 ppm for spot-free washdown and bottled-quality drinking water at every tap. When the boat is alongside, the same purifier runs on dock water.

It is supplied in modular or compact (stacked) frames, so it fits where the engine-room drawing allows: stacked units with locally mounted membranes, or a remote-mount configuration with the filters and membranes elsewhere. One 7-inch touchscreen runs both halves.

ข้อมูลจำเพาะ

Seawater capacity	Combinations from 900 to 2,200 US gal per day (3,406–8,328 L per day); configurations of 900, 1,200, 1,800 and 2,200 GPD
Purifier capacity	1,000 / 2,000 / 3,000 US gal per day (3,785 / 7,570 / 11,356 L per day); up to 125 gal/h
Feed water	Seawater, harbour or brackish water; dock water on the purifier side
ผลลัพธ์	About 10 ppm TDS or less from the purifier stage
พลัง	230 V 60 Hz, up to 19 A; 220 V 50 Hz, 17.3 A; 24 V DC control
Membranes	Filmtec high-rejection seawater membranes (watermaker); ultra-low-energy freshwater membranes (purifier)
Pre-filtration	Seawater commercial pre-filter 4.5 × 20 in; freshwater commercial pre-filter 4.5 × 20 in; bacteriostatic re-mineraliser 2.5 × 10 in; freshwater flush filter 2.5 × 10 in
การควบคุม	7-inch NEMA 4X colour touchscreen; automatic programmable freshwater flush; digital TDS; tank-switch input; mechanical override
Integration	NMEA 2000 compatible; optional second 7-inch remote touchscreen; optional tank level sensor
หมายเหตุการติดตั้ง	Boost pump installed below the waterline; wire-reinforced intake hose; clamshell inlet recommended before the seacock
Frame	2-in-1 modular or compact stacked frame; wall bracket option
Boat size	50–120 ft, per Spot Zero
การรับประกัน	12 months or 1,000 hours, parts and labour; Gold / Platinum / Diamond extensions available
ผลิตใน	USA

Capacity combinations (Spot Zero figures, per hour)

Combination (seawater / purifier)	Seawater stage	Purifier stage	Double pass*
XZ II 1200 / 1000	50 gal / 189 L	42 gal / 158 L	30 gal / 114 L
XZ II 1200 / 2000	50 gal / 189 L	83 gal / 314 L	30 gal / 114 L
XZ II 1800 / 2000	75 gal / 284 L	83 gal / 314 L	53 gal / 200 L
XZ II 2200 / 2000	92 gal / 348 L	83 gal / 314 L	70 gal / 265 L
XZ II 2200 / 3000	92 gal / 348 L	125 gal / 473 L	70 gal / 265 L

*Double pass is the total output when seawater is turned into spot-free water with the watermaker and purifier running together. Spot Zero positions the XZ II as its "Explorer" package: dock water and seawater in, pure water out, with Bluelink connectivity, the two-in-one RO design and auto-sensing smart switching between seawater and dock feed.

ทางไฟฟ้า

อุปทาน	Max draw	ความถี่	Phase
230 V	5.0 A at the dock (purifier only); 19.0 A at sea (both stages)	50 / 60 Hz	ชิ้นเดียว

Spot Zero notes that production capacity can be affected at 50 Hz: the pump motor turns slightly slower on a 50 Hz supply, so a system installed for Thailand is sized with that in mind. Tell us the daily water need and we will specify the capacity that delivers it on 50 Hz.

Dimensions and weights (Spot Zero drawings)

Stacked control units (purifier over watermaker)	538 mm W × 604 mm H × 315 mm D (21.2 × 23.8 × 12.4 in); 90 kg (200 lb) for the two control units
Modular control units	Two separate boxes, each 311 mm (12.2 in) high, mounted where the space allows
Locally mounted membranes (top view)	1,140 mm L × 442 mm D (44.9 × 17.4 in); stacked units 604 mm high
Locally mounted filters and membranes	1,140 mm L × 442 mm D; stacked units 669 mm (26.4 in) high
Purifier membranes (FW)	2000 GPD: one vessel 1,134 mm × 187 mm, remote or local; 3000 GPD: two vessels 1,140 mm × 419 mm, remote or local
Watermaker membranes (SW)	900 GPD: three short vessels 692 mm × 312 mm, local mount only on the stacked frame; 1200 GPD: two long vessels 1,162 mm × 231 mm, local mount on modular or stacked; 1800 GPD: three long vessels 1,160 mm × 314 mm, local only on stacked; 2200 GPD: four long vessels 1,162 mm × 419 mm, local only on stacked
SW and FW commercial pre-filters, 4.5 × 20 in (standard)	287 mm W × 197 mm D × 598 mm H each
Bacteriostatic remineraliser and fresh-water flush, 2.5 × 10 in (standard)	160 × 125 × 316 mm and 243 × 145 × 316 mm
SW boost pump (standard)	384 mm × 252 mm × 162 mm
ตัวเลือก	Short pre-filters (375 × 197 × 315 mm twin 4.5 × 10 in; 305 × 125 × 316 mm double 2.5 × 10 in); short membrane vessels (660 mm FW, 692 mm SW); remote 7-inch touchscreen 232 × 134 × 38 mm; wall bracket 598 × 314 × 274 mm, supports modular or stacked units

Installation, plumbing and wiring

The XZ II is two systems sharing one touchscreen, so the plumbing follows both of Spot Zero's flow drawings (linked below): on the seawater side, clamshell inlet, seacock, sea strainer and a boost pump installed below the waterline on 3/4 in ID wire-reinforced hose, pre-filter, then the watermaker control unit, with 1/2 in OD membrane lines, 3/8 in OD product and a 1/2 in OD concentrate overboard run free and unrestricted; on the purifier side, dock feed through 3/4 in ID tubing to the FW pre-filter, or the watermaker product as feed, 1/2 in OD supply and return, 3/8 in OD product through the bacteriostatic remineraliser to the tank, and the fresh-water flush cartridge fed from the ship's pressurised fresh water through a check valve. Spot Zero's wiring diagram ED1002-01 shows the watermaker and purifier boards linked, a single-phase inlet supply, the high-pressure pump in the system enclosure, 24 V DC touch panel and optional remote panel, an optional NMEA 2000 bus and an optional ship's tank-level switch through a 24 V relay.

XZ II-HD

For larger yachts Spot Zero makes the XZ II-HD, a three-phase 50/60 Hz version in five combinations from 2,400 / 2,000 GPD to 6,000 / 5,000 GPD (seawater / purified), in a 940 mm × 544 mm × 633 mm frame. It is quoted separately; ask us.

Service parts for this system

All of these are listed in our Spot Zero parts section at Spot Zero's US list price, special order from the factory with the lead time confirmed before you pay; tell us the model and serial number and we will confirm the exact membrane size and count for your configuration.

Watermaker side

SeaXchange Commercial Pre-filter (5) (FI-SW0005) — SeaXchange commercial pre-filter, 5 micron
SeaXchange Stage 1 Pre-Filter (25) (FI-SF0035) and SeaXchange Stage 2 Pre-filter (5) (FI-SW0003) — stage 1 and stage 2 cartridges for the short pre-filter
SeaXchange Freshwater Flush Filter (FI-SW0002) — fresh-water flush filter
SeaXchange Membrane 2.5" x 40" (MM-SW0001) — 2.5 × 40 in seawater membrane
SeaXchange Membrane 2.5" x 21" (MM-SW0003) — 2.5 × 21 in seawater membrane
O-ring Seal Kit - Membrane 2.5" (FI-SW0008) and O-Ring Kit, SeaXchange Membrane 2.5" (MM-SW0044) — O-ring kits
SeaXchange Membrane Chemical Cleaner, Stage 1 (MM-SW0012) and SeaXchange Membrane Chemical Cleaner, Stage 2 (MM-SW0013) — membrane chemical cleaners

Purifier side

Stage 1 + 2 Doublestack Pre-Filter / Oxidizer & Sediment Remover (FI-FW0005) — doublestack pre-filter cartridge
Spot Zero 4041 Membrane (MM-FW0010) — 4 × 40 in purifier membrane
Spot Zero Short Membrane 4021 (MM-FW0007) — 4 × 21 in short purifier membrane
O-ring Seal Kit (4041) Membrane (MM-FW0025) — O-ring seal kit
Spot Zero Membrane Chemical Cleaner (MM-FW0034) — membrane chemical cleaner
Bacteriostatic Re-mineralizer (FI-FW0017) — bacteriostatic remineraliser

Storage and controls

Preventative & Storage Solution (MM-SF0000) — membrane storage solution
PGDX XZII Remote Touchscreen Display (EL-DS0004) — XZ II remote touchscreen

Membrane care, storage and recommissioning (from Spot Zero's guide)

Fresh-water membranes sit in vessels closed with retaining plates (two M6 × 1.0 × 10 bolts, 5 mm Allen key) and are changed from the inlet end; the brine seal goes in last and is lubricated with a food-grade compound (Spot Zero recommends Molykote 111). Seawater membranes on the XTC II / XZ II side use 3/8 in quick-connect fittings on the end caps and three end-cap O-rings, which are replaced at every membrane change. New membranes ship in preservative and are flushed for at least 30 minutes with the product and concentrate discarded before the water is used.

If the boat is laid up, Spot Zero asks for the system to be run and flushed for five minutes once a month; if that is not possible, the membranes are preserved with Spot Zero's membrane storage chemical (one bottle per 5 US gallons / 18.9 L of purifier water, circulated with a chemical pump at no more than 30 psi and below 44 °C, renewed every three months). Recommissioning is a new pre-filter and a 30-minute flush to waste. The full procedure, with the freezing-climate version using propylene glycol, is in the membrane guide linked below.

Manufacturer documents

Spot Zero publishes the drawings and manuals openly; these are the current versions we work from:

What it costs

Spot Zero's US list price starts at US$32,000 for the XZ II. We quote per boat on the capacity combination and frame; freight to Thailand at cost, invoiced separately.

Next generation

Spot Zero's next-generation combination range (Combo 1200/1000 to Combo 2200/3000, plus three-phase Super Yacht models) with Bluelink is listed as coming soon; the XZ II is the current model and is available now. See Spot Zero Water Maker + Purifier — next generation.

การรับประกัน

Spot Zero's standard limited warranty on built-in systems is 12 months or 1,000 hours, parts and labour (membranes, filters, seals and other consumables excluded). Spot Zero's extended warranties — Gold (+1 year/1,000 h, parts), Platinum (+2 years/2,000 h, parts) and Diamond (+2 years/2,000 h, parts and labour) — can be added at any time during the standard term; ask us for the current prices. Warranty cover applies in whichever country the fault occurs.

How we supply Spot Zero in Thailand

Drake Marine supplies Spot Zero as a factory-direct purchase with our support around it: we size the system to the hull and its tankage, specify the 50 Hz configuration for boats staying in the region, handle the technical questions with Fort Lauderdale, support commissioning on the dock or in the shed, register the warranty, and keep the filters, membranes and service parts on order from Thailand rather than on a ship from Florida each time. Freight is at cost and invoiced separately, so the price you see is the equipment.

Tell us the boat, the tankage and where she will be kept and we will size the system, confirm the 50 Hz configuration for Thailand and quote the equipment with the factory lead time: LINE @drakeco, WhatsApp +66 99 406 4680 หรือ อีเมล.