Taking too long? Close loading screen.
Add to Wishlist

Owatrol C.I.P

$145.99

Clear
SKU: N/A Categories: , , Tags: , , ,

Description Specs

Owatrol C.I.P.

Owatrol C.I.P (Corrosive Inhibiting Primer) is a rust inhibiting primer which is suitable for finishing with both single and 2-pack paints and finishes. It contains the anti-corrosive properties of Marine Oil which enables it to stabilise the surface by penetrating deep into the substrate, driving out excess moisture and air to form a solid stable layer.

Owatrol C.I.P. is easy to use and does not require sand or shot blasting first. It can be used on both new and rusted surfaces. It will not dissolve or break down when even high solvent paints and finishes (urethane, epoxy, chlorinated rubber, synthetic, etc.) are applied to it and the pigmentation provides enhanced protection and perfect film-forming qualities. With Owatrol’s Marine CIP, sand or shot-blasted surfaces do not require immediate priming as a light rust coating will not affect its performance or the final result.

Ideal uses for Marine CIP rust inhibiting primer

  • Outstanding for high performance in severe conditions such as marine or tropical environments
  • Resisting corrosive fumes
  • Protecting ballast tanks of ships
  • Perfect protection where a high resistant paint or two-pack finish is necessary
  • Outstanding adherence on clean bright steel

 

At A Glance…

  • Accepts all paint types – Polyurethane, Epoxy, Chlorinated, Rubber, Car paints, etc.
  • Ideal for difficult conditions such as marine environments
  • Stabilises the surface whilst penetrating the substrate, driving out excess moisture and air
  • Provides a solid stable layer that other paints can firmly adhere to
  • Minimal preparation required – eliminates the need for sandblasting

 

Application Guide

Surface Preparation

Surfaces must first be clean, dry and free from oil, grease and other surface contaminants. Remove all mill scale; loose and flaking rust and old paint back to a sound surface and edge and feather in any sharp edges. Any surfaces exposed to chemicals (acids, alkalis or salt deposits) should be washed using copious amounts of water or steam cleaned. Severely contaminated surfaces should be cleaned using an appropriate solvent.

 

Application of Marine CIP Corrosive Inhibiting Primer

Stir well before and during use.
Do not thin.

 

Applying CIP to new surfaces

Prime with 1 coat of Marine CIP and allow to dry. For surfaces subject to aggressive climatic conditions apply 2 priming coats.

Applying CIP to clean, lightly rusted or new unpainted rusty steel

Apply 2 coats of Marine CIP allowing drying time between coats.

 

Applying CIP to old or severely rusted surfaces

Either apply 3 coats of Marine CIP allowing drying time between coats or apply wet on wet applications of Marine Oil until the rust is fully saturated and allow to dry for 24 hours and then apply 2 coats of Marine CIP allowing drying time between coats.

 

Applying CIP to previously coated surfaces

First spot prime all exposed metal with 2 coats of Marine CIP allowing drying time between coats and then apply a 3rd coat over the entire area and allow it to dry.

 

Clean Up

Clean all tools and equipment with white spirit while still wet. If allowed to dry, remove with paint stripper.

 

NOTE: Any rags, steel wool etc. soaked in CIP may spontaneously catch fire if improperly discarded. Rags, steel wool etc. must be saturated with water after use or placed in a sealed, water filled metal container, before disposing with household waste.

 

Things to Remember

  • Cover everything you do not wish to paint.
  • Apply between 5˚C and 35˚C.
  • Do not apply in direct sunlight or on to hot surfaces.

 

Contact us for details!

Container Size

0.75 Litre, 2.5 Litre, 20 Litre

Coverage

15m2 per litre

Tools

Brush, Roller, Airless Sprayer

Suitable For

Exterior & Interior use

Clean Up

White Spirit

Drying Time

6 hours

Re-coating Time

24-72 hours depending on finish – C.I.P. 24 hours; oil/alkyd paints 24-48 hours; high solvent paints i.e. 2 pack, urethane etc 48-72 hours

Suitable Surfaces

Ferrous and non-ferrous metals

Product Rating

  • 5 STARS (0)
  • 4 STARS (0)
  • 3 STARS (0)
  • 2 STARS (0)
  • 1 STARS (0)
0 / 5

Overall Satisfaction Rating Based on 0 ratings from customers

Customer Reviews

Your email address will not be published. Required fields are marked *

Reviews